![](https://img.alicdn.com/imgextra/i1/74422955/O1CN01rfpB2B1XhQyvT1BKv_!!74422955.jpg)
After the production of pound cake molds of the French company M was discontinued, the bakery shops and bakery teachers all hope that Japan can produce molds of the same quality.
Therefore, Yoshida store in Japan launched a new series of pound cake molds this time.
In the words of Yoshida store employees, this is a mold that can become a baking heirloom!
Times have changed. Mom passed the baking mold to her daughter. This mold can still show its good performance!
![](https://img.alicdn.com/imgextra/i1/74422955/O1CN01BVKmgr1XhQyuiISRD_!!74422955.png)
![](https://img.alicdn.com/imgextra/i4/74422955/O1CN01RzIdgt1XhQyy0K0cX_!!74422955.jpg)
Features of this mold:
Use special custom-made plates, good heat conduction;
The bottom of the whole piece is cut, and the leakage of the four corners is improved compared with Yoshida''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s ordinary pound cake mold;
Brass wire is used at the crimping, which has high appearance and is not easy to rust;
Silicon processing coating treatment, easy demoulding.
*As the number of uses increases at any time, the coating gradually loses its effect.
At that time, apply unsalted butter and burn the mold in an empty state. Apply an appropriate amount of unsalted butter before each use. After refrigerating the mold, pour the batter into the oven, and the mold can still be demolded smoothly.
![](https://img.alicdn.com/imgextra/i4/74422955/O1CN01qfYzl81XhQyt2m3bd_!!74422955.jpg)
Product supplementary description:
1. The four corners of the mold are not completely sealed. Put in a low-viscosity batter, which may cause liquid leakage.
2. This product is a semi-handmade product, slight scratches cannot be avoided, and the corners are not specially polished and are not smooth enough. Please also understand.
3. Note: The heat-resistant temperature of the coating is 220 degrees. If the temperature exceeds this temperature, the coating may wrinkle.
![](https://img.alicdn.com/imgextra/i3/74422955/O1CN01AiZ1gd1XhQzd1xUJm_!!74422955.png)
Instructions for use:
1. Before using for the first time, please clean the mold with detergent and grease it. No need to burn.
2. It is recommended to use oil, which not only has a better demoulding effect, but also has the effect of maintaining the mold.
3. This product is only for oven, please do not use it for direct fire.
4. Do not use steel wire balls, hard scouring pads, etc. to scrub the mold.
5. After use, please wipe off the water vapor and dry it completely and store it. It is best to put it in a kitchen towel and wrap it with a kitchen towel before storing. The moisture in the air may cause the mold to rust.
6. Can not be used in dishwashers, tableware dryers.