![](https://img.alicdn.com/imgextra/i4/398075030/O1CN01qb4l1T1n1mnLBTzHZ_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i2/398075030/O1CN01v7Ohdy1n1mq1xAteL_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i1/398075030/O1CN01Kqeu5o1n1mnUGfUhk_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i3/398075030/O1CN01neabNG1n1mncaihAn_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i2/398075030/O1CN01owm1N81n1mncXUUiC_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i4/398075030/O1CN017ux7z91n1mnf5f2Cz_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i2/398075030/O1CN01hiufbq1n1mnf5dYiy_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i3/398075030/O1CN01hdprUN1n1mne5EC4X_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i4/398075030/O1CN01wYO8oW1n1mndS3T1D_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i4/398075030/O1CN01qOFxmM1n1mnZuBGhH_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i1/398075030/O1CN011rStcx1n1mnbkIuQy_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i2/398075030/O1CN01X2Di0G1n1mncAftYP_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i4/398075030/O1CN01as5QGs1n1mnf5i3ZG_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i1/398075030/O1CN01dG6iLm1n1mq2vo3AO_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i1/398075030/O1CN01Rybjlk1n1mq2ECsOS_!!398075030.jpg)
![](https://img.alicdn.com/imgextra/i4/398075030/O1CN01myz7j81n1mq5cmlUO_!!398075030.jpg)
★Pre-post preparation:
1: Prepare tools: tweezers, hair dryer(If not, find a lighter), Paper cutting knife, alcohol bag, cleaning cloth.
2: Wash your hands, prepare a clean desk or workbench, sit in a quiet and bright environment, and relax.
★Work in post:
1: After receiving it, first remove the excess stickers according to the hollow in the drawing, and cut out all the internal round holes and special-shaped waste paper.
2: Wipe the camera clean with an alcohol bag in the paste, and then study the corresponding position of each hole after it is dry.
3: The correct order for most of the paste is: paste the part with many holes first, then paste the small area, start from the top, then paste the front and back holes, then paste the bottom and skin.
Use a hair dryer to smooth the warped edges after applying one or two stickers.
★Notes:
1: The most difficult thing to paste is the part with many holes. It must be carefully aligned. If the paste is not correct, it can be peeled off for multiple tests. The carbon fiber is flexible. If it is shorter than 1 mm, it can be fired.(hair dryer)Heat for one or two seconds to stretch. If it is about 1 mm too large, just heat it once, and the extra part of the belly will automatically disappear.
2: Be sure to align the holes first and then smooth and press by hand. If you encounter a large porous sticker, try cutting in half from the smallest part to reduce the difficulty of filming; if there are holes on both ends, both ends Align the holes respectively and then smooth the middle. If there is a raised part that does not fit, use a cutting method to eliminate the raised part, and then flatten it left and right.
3: Press and smooth every few small pieces, and then heat to fix the corners. After all the work is finished, you can press it with a hair dryer to make sure that each piece fits the camera completely.
This is a work process that tests patience, you guys must be patient, work quietly, don’t be impatient, slow but not easy. Finally, I wish the pasting machine success and protect the camera.(Lens)Anti-wear, beauty camera overall effect.