Suitable for bicycles and electric bicycles with steel wheels;
The meter head is plug-in type (unplug at any time to prevent theft);
Easy to install, with only two screws and two plastic cable ties;
It can be installed in five minutes.
Note: Keep the sensing distance between the probe and the magnet 3-5mm. Otherwise the speed value will jump randomly! .
Tire circumference setting function
1. Set according to the circumference of the bicycle tire.
Speed ??function:
2. Instantaneous driving speed SPD
3. Maximum driving speed MXS
4. Average driving speed AVS
5. Comparing with the average speed reminder▲▼wheel revolution function
6. R mileage function(English/Metric switch)
7. Total mileage ODO
8. Single driving mileage DST
9. The initial value of total mileage is set. If the battery is replaced, the value before the replacement can be set as the initial value.
Time function
10. Driving timeTM
11. clock(12 hours/24 hours switch)CLK automatic cycle display function
12. ODO, DST, MXS, AVS, TM, R, CLK function, automatic scrolling display SCAN every 4 seconds
Driving data sampling function
13. Real-time data sampling, professional testing, including DSTTMAVSMXS
Power saving function
14. If there is no input signal within 30 seconds, it will automatically enter the power saving mode, and only the time will be displayed.
Maintenance reminder function
15. When the total mileage reaches the set maintenance value, the wrench symbol is displayed to remind the bicycle to be maintained.
water-proof
16. Has good waterproof function.
installation tips:
1. Install the meter head base on the handlebar;
2. Insert the AG13 button battery into the battery slot on the back of the meter
3. Initialize the code table data, generally only need to set the tire circumference as a parameter, then it can be used normally;
3. Insert the meter head into the slide groove of the meter head seat;
4. Install the sensor on the front fork, with the sensor head facing the spokes;
5. The induction magnet is installed on the spokes, aligned with the induction head, and the distance is about 3-5mm;
6. Fix the cables with nylon cable ties;
7. Check whether the above meter head base, sensor and induction magnet are installed firmly. This package comes with necessary rubber gaskets and detailed instructions in Chinese and English to ensure your installation is successful.
8. For more functions, please refer to the manual settings
Setting function
1. Install the battery into the battery slot on the back of the meter;
2. Press the right button within 15 seconds to enter the tire circumference setting;
3. Refer to the wheel diameter and circumference comparison table. For example, the wheel circumference of the 28 model is 224cm, press the left button to set the three-digit value to 224(The machine defaults to 208cm)
4. Right click to confirm;
1. The speed is always 0 when driving
Answer: The distance and angle between the magnet and the sensor is incorrect(Try to keep it within 5MM)
2. The numerical display is not correct when in use
Answer: The set parameters are incorrect(Such as the circumference of a bicycle wheel)
3. Display slow response
Answer: When the bicycle watch works below 0 degrees, the temperature will return to normal when the temperature is restored.
4. Black screen
Answer: Exposing to the sun for too long, leaving it in a dark place for a period of time to return to normal
5. The display is weak
Answer: The battery contact is not good or the battery is dead, check the battery installation or replace the battery.
6. The display number is missing
Answer: Take out the battery and wait for 10 seconds before reloading it.
Code meter modulation installation instructions
Step 1: Use a coin to open the back cover of the stopwatch, take out the battery slice inside, reinstall it, and close the back cover.
Step 2: After operating the first step, a factory value of 2060 will come out. We see that the last 0 of 2060 is beating. Next, we take the 26-inch 1.95 inner tube as an example, the corresponding circumference is 2055.
Step 3: Let''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s talk about how to adjust 2060 to 2055.
1. Just now we said that the 0 of 2060 was beating when the factory value was released. At this time, we press the right button, adjust this 0 to 5 and then press the left button.(At this time, the right button is for digital adjustment, and the left button is for confirmation.)
The same is true for other digital adjustments.
2. When it is adjusted to 2055, we press the left button again and see a clock sign, and then it is 0:00
At this time, if we hold down the left button for about 2 seconds, a 24-base system will come out. This is to modulate the clock.
Click the right button after the 24-digit number is displayed, and the form of 0:00 will be displayed.
At this time, use the left button to adjust the front 0 to the corresponding hour and press the right button to confirm, and jump to the rear 00 to adjust to the corresponding minute.
3. At this time, we see the required interface: the same as the above display speed(km/hr)Here is the time.
In this case, we will adjust the time and circumference.
Step 4: installation
Before installing it, take the code table in your hand and test it to see if there is any data response.
1. After fixing the head of the computer to the base, you hold the transmitter in one hand and the magnet in the other to grind it back and forth, and see if the speed is not displayed. If there is any, you can load it again.
2. The meter head is installed on the car, the transmitter is installed on the right front fork, and the distance between the magnet and the transmitter is about 3MM.