Di622Mark II specifications

• Flash guide number (GN value), up to 32 (ISO100. M, 35mm focal length) or 44 (ISO 100. M, 105mm focal length)
• The Di622 Mark II flash is the current fast auto-zoom flash, which supports a flash zoom range of 24mm– 105mm, when the diffuser is put down, it is about 16mm
• Manual light intensity switching function (1/1 FULL full output, 1/2, 1/4, 1/8, 1/16, 1/32 total 6 levels)
• Supports jumping lights, the lamp head can be raised up to 90 degrees in the vertical direction, and it can also be used for indirect lighting by 180 degrees to the right and 90 degrees to the left.
• Support SD, SF light trigger, SD is general light control, SF is pre-flash avoidance control
• Support Canon 580EXII, Nikon SB-900, SB-800 coordinated operation, can be booked in CH1 Group A, and support TTL wireless control
• Support standby mode, automatic power saving mode
• Support focus assist light
• Can be operated through the camera to control rear curtain synchronization, dimming compensation and FE lock
• Use 4 AA batteries as power source
• Normal recycle time is about 0.3sec– 4.7 sec, about 4.7 seconds of recycling time at full output
• Size is 77x 130x 103mm
• The weight is 315g

Compatibility list, of course, it is not only compatible with the following models, subsequent models will also be supported

Di622 Mark II For Canon [Ver.1.0]
EOS-1D Mark IV/1D Mark III/1D Mark II N/1D Mark II
EOS 5D Mark II/5D/7D
50D/40D/30D/20D/10D
EOS 550D/500D/450D/350D
EOS 1000D

Di622 Mark II For Nikon [Ver.1.0]
D3X/D3S/D3
D2Xs/D2X
D700
D300s/D300/D200
D90/D80/D70s/D70
D3000/D5000
D60/D50/D40x/D40

 Firmware upgrade

After you purchase the Di622 Mark II that supports Nikon''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s i-TTL flash system or Canon''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s E-TTL flash system, the Di622 Mark II can be upgraded through firmware to ensure that the flash can continue to be used on new models of cameras of this brand. This function can greatly protect your long-term and reliable investment in Nissin Flash.

List of appearance designs
▼ Although it is a mid-level flash, it has a larger lamp cap design, as well as a diffuser and reflector design.

▼ The mode button on the back is changed to M, SD, SF and Ch1 Group A to support more diversified wireless flash control
When switching modes, the color of the light will also be different, for example, Ch1 Group A will turn purple

▼ On the right side of the light, the battery slot is placed on the right side of the flash.

▼ With enhanced light receiver and focus assist device

▼ The bottom contacts of the flash are divided into Nikon and Canon versions. It is still a plastic base.

▼ When opening the battery room, use four AAA batteries

▼ There are two connection holes for the sync line on the side, one is the X-Sync jack, and the other is a jack the size of a standard headphone connector

▼Front view, Di622 Mark II has a larger lamp holder. From the lamp holder, it is quite close to the momentum of an advanced flashing light.

▼ Di866 MarkII with a big bucket on the back.

▼ When turning the head to the left (90 degrees).

▼ Turning 180 degrees to the right is equivalent to turning the whole back.

 

Description of each part


Specifications

In the new version of the Di622 Mark II flash, the design of the Di622 Mark II’s rear button has been adjusted, and the CH1 Group A button has been added to support Canon or Nikon’s wireless TTL remote control, and can be used as The main lamp or the auxiliary lamp is used when multiple lamps are used. On the side, there are two more SYNC jacks. In order to enhance infrared support, the ability to receive infrared has also been enhanced.
The Di622 Mark II flash is a functionally increased version of Di622 in terms of positioning. It has decentralized many high-end flash functions to enhance its competitiveness in the mid-end flash market. The important point is that Di622 Mark II will be a mid-level flash that is very suitable for off-camera control of multiple flashes. It has the good texture of Japanese design brands and can be controlled in M ??mode (SD, SF two modes), light Triggered by TTL control (CH1 Group A), wire control... etc.

Di622Mark II is a powerful slave unit wireless remote flash.
You can enjoy creative flash photography with multiple flashes from different directions. There are 3 slave flash modes available:
Digital Servo（SD）: Di622 Mark II can recognize TTL flash with pre-flash. Can be remotely triggered by any digital TTL flash（Mainly applicable to Canon''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s E-TTL and Nikon''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s i– TTL flash）.
Film servo（SF）: Di622 Mark II can be triggered by a traditional single flash in this mode. The flash output level of the flash is manually set. The flashing lights in the studio can also be remotely controlled simultaneously in this mode. This is an open remote mode flash that can be used by mainstream flashes on the market.
Wireless TTL: Di622 Mark II can match the intelligent wireless TTL off-camera flash control system as a slave unit of wireless TTL flash for automatic control. The master flash is preset to channel 1, group A status.
TTL flash exposure compensation
TTL flash exposure compensation that the flash can still perform in TTL flash mode.
The main function is: the exposure compensation on the flash can only control the brightness of the subject, and does not have a significant impact on the exposure of the environmental background.
The flash exposure compensation level is divided into 0.5EV steps, and can be adjusted from +1.5EV to -1.5EV.
Nissin flash unique“My TTL”Settings
you can use it“My TTL” Function to customize the flash output of Di466 under TTL auto to make it more in line with your requirements. You can make the flash under TTL
The standard flash output is slightly higher than that of the staggered range. The range is between -0.75 EV and +0.75 EV, divided by 0.25 EV. Restart the flash after setting
You can save the settings you have made.
X terminal external flash sync
Di622Mark II can be used with cameras without flash shoes. Some cameras only provide an X terminal to connect the flash, instead of the common sync hot shoe.
For this type of camera, Di622Mark II has a flash sync X terminal jack, which can be triggered by connection.
High Power
G.No.62（ISO 200）At 105mm, the value is about 45 at 35mm.（Reference: The built-in guide number of the flash of a general camera is about 16, ISO 200）.
Auto zoom lamp holder
The illumination angle of the flash can be automatically zoomed according to the angle of view of the installed lens. The zoom system driven by the stepping motor achieves high speed, making the flash head and the lens
The zooming of the head is synchronized almost unaware.
Energy saving system
Di622 Mark II has a dual energy saving system.
When there is no operation for more than 2 minutes, it will automatically enter sleep mode. At this time, half-press the camera shutter or touch any button on the flash to reactivate it. If no operation is performed for more than 30 minutes, the flash will automatically shut down. In the slave mode of the wireless off-camera flash, the sleep mode will be cancelled, and the automatic shutdown time will not proceed.
Extend to 60 minutes during any operation.
Manual flash
In manual flash mode, the output power of the flash is from full power output to 1/32, adjustable in 6 levels.
Autofocus auxiliary light
In the dark or dim light conditions, Di622 Mark II can emit a sharp contrast auxiliary focusing beam, making the camera''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s autofocus easy.
Flash exposure lock function
The Di622 Mark II flash is compatible with Canon''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s FEL flash exposure lock function or Nikon''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s FV lock function.
Please refer to the detailed information manual of the camera owner.
Rear curtain synchronization.
Some digital cameras from Nikon and Canon can be set to flash sync with rear-curtain sync. This function needs to be set from the camera menu.
Red-eye reduction
Only for Nikon cameras. Before the formal flash exposure, the flash emits a short strobe to stimulate pupil contraction to prevent red-eye.

Di622 Mark II N and Nikon（Nikon）DSLR camera system compatibility list:

D3X / D3s / D3 / D2Xs
D700(FV lock system does not work)
D300s / D300 / D200 / D90 / D80 / D70s / D70
D3000 / D5000 / D60 / D50 / D40X / D40
Fuji FINEPIX S5 Pro(FV lock system does not work)

Di622 Mark II C and Canon（Canon）EOS DSLR camera system compatibility list:

1D Mark IV / 1D Mark III / 1D Mark II N / 1D Mark II
5D Mark II / 7D / 5D
50D / 40D / 30D / 20D / 10D
550D / 500D / 450D / 400D / 350D / 300D / 1000D
PowerShot G7 / G9 / G10 / S5 IS / SX10 IS

Note: When a non-original lens is used on the camera, there is no guarantee that the flash will work normally.