goumai
Accessories such as heightened motor seat, landing gear, belly wheel and motor extension cable are not included in the empty machine, please take a separate photo if you need it
Precautions:Empty planeNo electronic accessories,Does not contain Y wire,You also need the following to complete the flight:
Motor, ESC, propeller, 4 steering gears, 2 steering gear extension cables(The line is not long enough), 1 servo y line(Two aileron servos are connected in parallel), Foam glue, battery and charger, remote control and receiver.
Specific models are recommended as follows:
- Motor:New Sida xxd2212 2450kv, or Langyu x2212 2450kv, or Yinyan 2205 2300kv, etc., in short, it is high kv with small propellers(Space is limited, and big oars can’t be installed.If you have to use a low kv with a large propeller, you can choose a motor to increase the seat)
- Note: An extension cable is required between the motor and the ESC! !
- ESC:20A to 40A ESC, don’t blindly pursue a big one, the suitable one is the best. A 20A ESC with a 2212 class motor is sufficient.
- propeller:5-inch three-blade propeller or 6-inch propeller, you can use 8-inch propeller if you choose to increase the motor base(It is recommended to use a reverse paddle)
- Servo:4 pieces, 8g or 9g or 12g, specific models, such as Yinyan 08ma, Yinyan 08a, Yinyan 08md
- Extension cord2 pieces,y line1 piece, 30 to 50 cm
- Foam glue: Foam glue, not 502, ab glue, etc., will corrode the foam, white latex or 502 glue can be used for wood chips
- Battery:Suggest 1300-2200mah 3s
- charger:Simply choose the b3 charger or the b6 series, pay attention to the need for balanced charging
- Remote control and receiver:Need 4 channels or more
For specific introduction of these devices, please visit www.datanovo.cn website, all of which are introduced in different categories
If you already have some of these items in your hand, you don’t have to buy them again, such as batteries and chargers(The charger needs a model airplane balanced charge), Remote control and receiver(Requirement is a remote control and receiver common to model airplanes, excluding toy remotes)
Focus on the point: Our store launches considerate service: all electronic circuits are done for you, and no welding operation is required to go back!
The recommended configuration for novices is as follows:
Primary power package:(By default you have the remote control, battery and charger):
Motor xxd 2212 2450kv 1 + xxd ESC 30 A 1 + 6040 Qianfeng nylon propeller 2 + Servo Yinyan 08a 4 + 2 30 cm extension cords + 1 30 cm Y wire + 1 foam glue + 3 motor extension cords + 1 roll of fiber tape
Advanced power package:
Longyu x2212 2450kv motor 1 + Zhongtewei 30a ESC 1 ++6040 Qianfeng Nylon Propeller 2 pcs + Servo Yinyan 08a 4 pcs + 2 30 cm extension cords + 1 30 cm Y line + 1 foam glue + 3 motor extension cords +1 roll of fiber tape
Another tip:If you don’t have a battery, don’t forget to buy a power battery separately: 1300mah 3s or 2200mah 3s
Full package:In this case, it is assumed that you have nothing, even a remote control, and no battery. First of all, a few suggestions: aircraft models require a lot of time and energy investment, to practice flight simulators, to learn the use of various electronic devices, If you want to repair the aircraft after bombing it, you can enjoy the joy and pleasure of flying repeatedly, so please be prepared first.
- Power package + Grignard battery 2200mah 3s + BB ring 1 + b3 charger + mc6c remote control set(With receiver))+ Emulator(If you don’t practice the simulator and fly directly for the first time, you will definitely blow up)
You can also choose RADIO at9s remote control kit instead of mc6c remote control, which has more functions and more powerful
In addition, please visit www.datanovo.cn to learn the basics first, and contact our customer service if you have any questions to help you enjoy the fun of flying smoothly.
Assembling and using the catapult frame in our shop:
http://www.datanovo.cn/course/detail/110
Accessories detail display(Delivery is not assembled):
Installation instructions for Surfer X8:
http://v.youku.com/v_show/id_XOTQ5NDEwOTgw.html
Video viewing address:
http://v.youku.com/v_show/id_XMzE1NzI3MTQ0.html?firsttime=0&from=y1.4-2
Surfer X8 installation complete debugging video(Secret 1118):
http://v.youku.com/v_show/id_XMTQ0NDYwNjcxNg==.html?firsttime=1245&from=y1.4-2
Empty machine does not contain Y wire