![](https://img.alicdn.com/imgextra/i3/61322388/T2zExlXndMXXXXXXXX_!!61322388.jpg)
![](https://img.alicdn.com/imgextra/i3/61322388/T20ahJXotXXXXXXXXX_!!61322388.jpg)
Product Name: Leather Shift Dust Boot
Material: first layer of yellow leather
Color: black leather and red thread black leather and black thread
Suitable models: Fox manual gear
Remarks:The dust cover is only a leather case, without the gear base. The base removed from the original dust cover must be used for installation.
Included: a stick of viscose(For sticking base)
![](https://img.alicdn.com/imgextra/i4/61322388/T2O.VlXlxMXXXXXXXX_!!61322388.jpg)
★This product is only a leather case for the gear lever dust cover, as shown in the actual product picture, (not including the gear head and the plastic frame of the base, the others are removed with the dust cover of the original car) ★
![](https://img.alicdn.com/imgextra/i2/61322388/T2enakXbxbXXXXXXXX_!!61322388.jpg)
![](https://img.alicdn.com/imgextra/i4/61322388/TB2NWRvtb4npuFjSZFmXXXl4FXa_!!61322388.jpg)
![](https://img.alicdn.com/imgextra/i4/61322388/TB2uA2SsHtlpuFjSspoXXbcDpXa_!!61322388.jpg)
![](https://img.alicdn.com/imgextra/i3/61322388/TB2vK4Rc9vHfKJjSZFPXXbttpXa_!!61322388.jpg)
Description:Dust cover before model 08Upper approachIt’s a bit different from the original car, the original car(Old style)The upper sleeve of the dust cover is made of rubber band, and there is a small opening(Not sealed), And it will wrinkle after tightening. When the dust cover is installed, the upper part is replaced with a tie strip or an iron wire, which will be more smooth and beautiful after being turned over.
The Fox dust cover after the 09 model directly follows the original installation method of the original car.
![](https://img.alicdn.com/imgextra/i1/61322388/T29.8lXghMXXXXXXXX_!!61322388.jpg)
★★Removal and assembly legend of the old gear lever dust cover:
1. Unscrew the gear head counterclockwise and pull out the panel upwards;
2. Decompose the old set;
![](https://img.alicdn.com/imgextra/i4/61322388/T2.o4lXeJMXXXXXXXX_!!61322388.jpg)
3. Glue the newly-applied glue back to the base, and then put it back into the bright frame.
Then the upper mouth of the dust cover is tied in the groove under the head with a tie, as shown below(For old Fox), And finally put it back in the car.
![](https://img.alicdn.com/imgextra/i4/61322388/T22qpJXdRXXXXXXXXX_!!61322388.jpg)
★★Assembly and disassembly legend of the new gear lever dust cover:
Steps 1 and 2 are basically the same as the old one; the new gear lever dust cover is stuck under the gear head. Pry open the plastic rubber ring under the gear head, and then the dust cover can be removed, as shown in the figure below;
![](https://img.alicdn.com/imgextra/i3/61322388/T2qTqnXgpaXXXXXXXX_!!61322388.jpg)
3. The dust cover of the original car is fixed on the base with staples, the base frame can be separated by removing the staples, and the new leather cover uses glueJust stick it back to the base, of course, you can also use which staples to fix it according to the original car. Put on the bright frame and put it back on the car.
![](https://img.alicdn.com/imgextra/i3/61322388/T2unqnXglaXXXXXXXX_!!61322388.jpg)
![](https://img.alicdn.com/imgextra/i4/61322388/T2ntFSXoXcXXXXXXXX_!!61322388.jpg)
Note: Many car owners did not lift the panel when removing the dust cover, but went directly to the plastic frame of the dust cover. Due to improper force, the base of the plastic frame could easily be broken. Frame, don''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''t use too much force, try to start from the back two corners. Or cut off the old dust cover and break off the plastic frame of the dust cover for better operation.