Realize the same network cable to watch TV and surf the Internet through multiple multicast IMGP
Extended soft routing multi-wan dialing
Support loop detection and blocking
Port aggregation
Users can add/delete aggregation or change port groups. It should be noted that aggregation 1 can only include port 1 to port 4, and aggregation 2 can only include port 5 to port 8. In the following cases, aggregation cannot be added:
（1）The aggregation includes only one port.
（2）Ingress/egress rate control of any port in the group is enabled.
（3）The connection speed/port duplex of the port is not the same.
Loop detection and prevention
Users can configure loop detection or loop blocking, or close.
Bandwidth control
Users can change the ingress/egress bandwidth rate of each port.
Network storm control
The storm control information of broadcast packets, multicast packets, unknown multicast packets and unknown unicast packets displayed on the page. The user can enable/disable the four storm control functions of the port, and the specific rate should be set as required.
Cable detection
The user can open the cable diagnosis function in the background, and the cable length/status on this page. Cable diagnosis is measured by RTCT here“Cable fault distance”. When the cable is broken, we can see“Test result” Show submitted“Open”, you can use“Cable fault distance”Get the distance of the disconnection. .
Zhipulian-SG1008M switch is independently designed and developed by Zhipulian electronic technology.A new generation of simple network management switches specially designed to meet network requirements, with complete security strategies, complete QoS strategies,Rich VLAN features, easy management and maintenance, etc. The system adopts a brand-new software and hardware platform, in the security access strategy, multi-service supportIt provides users with brand-new technical features and solutions in terms of support, easy management, and maintenance. It is an ideal office network, campus network, andAccess layer switches for small and medium-sized enterprises and branches
Setting example
Expand wan settings
1 mouthIn order to connect to the routing VLAN aggregation port, ports 2-8 are a VLAN 2-8 respectively.
First of all, Fill in 2 in the VLAN number, which means VLAN ID 2. The VLAN name can be any, in this example, broadband 1 is usedThenSelect Tagged for port 1, and Untagged for port 2,Then click increase. Then set up VLAN3, alwaysTo VLAN8
The result after setting is as follows
After the VLAN ID is set, enter the VLAN port settings and set the PVID of the port to be consistent with the VLAN ID.The received frame format is ALL, as shown in the figure below:
Isolation + anti-loop setting
Loop detection and prevention
This page displays the current loop detection/loop blocking function status. Users can configure loop detection or loop prevention, or close.
Port isolation
This page shows the configuration of port isolation. The user can set the ports that need to be isolated. The left port is the port that needs to be isolated, the rightThe side forwarding port is the uplink port, for example, select Port1-Port7 on the left（Hold down the Ctrl key of the computer to select multiple）, Select on the rightPort8, after clicking the application, ports 1-7 are isolated and cannot communicate with each other, and can only communicate with port 8. As shown below
Port mirroring packet capture settings
This page displays the mirroring function of the switch. The user can set the mirror port on this page.
Select Both for the mirror setting, the mirror port refers to the port that receives the mirrored data, and the mirrored port refers to the port that needs to be mirrored.
The software supports mirroring the data of multiple ports with one port at the same time.
After setting, please click save in the tool, otherwise the power will be cut off and the setting will be lost
| Transmission rate | 10Mbps/100Mbps/1000Mbps |
| Network standard | IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.1Q |
| Network protocol | CSMA/CD |
| Port structure | Non-modular |
| Number of ports | 8 10/100/1000Mbps adaptive ports |
| Network medium | 10Base-T: Category 3 or above UTP/STP |
| 100Base_TX: Type 5 UTP/STP |
| 1000Base-T: Super Category 5 or Super Category 5 UTP/STP |
| Exchange method | Fast store and forward |
| Backplane bandwidth | 16Gbps |
| Packet forwarding rate | 10Mbps:14880pps;100Mbps:148800pps;1000Mbps:1488000pps |
? Conform to IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z standards;
?SR-S8808M provides 8 10/100/1000Mbps adaptive RJ45 ports.
? Adopt two-level user management mode to enhance the management security of the switch;
? Full-duplex flow control conforms to IEEE 802.3x standard, half-duplex adopts Backpressure standard;
? The port supports auto-negotiation function, automatically adjusts the transmission mode and transmission speed;
? Support 8K MAC address;
? Support MAC address automatic learning, automatic aging and aging time setting;
? Support static MAC address, filtering MAC address, dynamic MAC binding and other address table management functions;
? Tag VLAN based on IEEE 802.1Q;
? Support port security control, broadcast storm suppression and other functions;
? Support port-based ingress/egress bandwidth control;
Support loop detection and loop prevention functions;
Support port bandwidth control function;
? Support port aggregation function;
? Support port mirroring and traffic statistics functions;
? Support QoS function;
? Provide convenient and easy-to-use WEB visual management;
Size: 138*74*27mm
Shell material: iron shell
Template protection code
Template protection code
Template protection code